CDRInfo Forum CDRInfo Forum

Forums  Register  Login  My Profile  Inbox  Address Book  My Subscription  My Forums 

Photo Gallery  Member List  Search  Calendars  FAQ  Ticket List  Log Out

Help with a "burning" issue...   Logged in as: Guest
Viewers: 1429 You can click here to see Today's Posts | Most Active Topics | Posts Since Last Visit
  Printable Version
All Forums >> [Optical Storage] >> CD, DVD, BD Drives >> Help with a "burning" issue... Page: [1]
Login
Message << Older Topic   Newer Topic >>
Help with a "burning" issue... - 11/24/2007 5:01:20 PM   
chugbug

 

Posts: 5
Joined: 11/24/2007
Status: offline
Hello All,

I have a Pacific Digial Mach 52 CDRW (shows in hardware list as CDWRITER IDE5224).  For some reason, a few months ago, I started having problems burning disks with it.  Today, I updated the firmware, then tried to burn a test disk.

Using NERO 6, I burned a disk with 362MB of files/folders.  According to the log, the burn was sucessful, but the verification found errors.  I checked the burned disk, and it opens fine, has the same amount of data/files/folders as it should, and I can read the disk.  Hoping it was a fluke, I burned another, but the same thing happened.  Anyone have any suggestions as to what the problem may be?  Listed below is the log from the last burn.

Also, Now a more pressing issue... I went into my Device Manager for the exact name that the CDRW disk is shown, and I noticed that now my DVD burner is "X" out and disabled.  I attempted to enable it, but Windows says it can't.  I KNOW I upgraded the firmware to the correct drive (I made a copy of the window after it was finished, and it shows the correct drive was selected).  So now, it appears I have two problems!

I wasn't too concerned about the issue with the CDRW, since it seemed to have burned the data, plus I had my DVD burner to use instead.  But now that I can't access my DVD drive, I need to figure out what happened to it.

Can anyone give me some recommendations to my problems 1) DVD drive not being able to be enabled, 2) why my CDRW burns appear to be not burrning exactly as it should.

Thanks...Chugbug

-------------------------------------------------------------------------
NERO 6 Burn Log:

John E. Brady
[REMOVED]
Windows XP 5.1
IA32
WinAspi: File 'Wnaspi32.dll': Ver=4.71 (0001), size=45056 bytes, created 5/28/2003 6:53:46 PM
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM
NT-SPTI used
Nero Version: 6.6.1.4
Internal Version: 6, 6, 1, 4d
(Nero Express)
Recorder:             <CDWRITER IDE5224>        Version: 001H - HA 1 TA 0 - 6.6.1.4
Adapter driver:      <IDE>                     HA 1
Drive buffer  :      2048kB
Bus Type      :      default (0) -> ATAPI, detected: ?
CD-ROM:               <CDWRITER IDE5224         >Version: 001H - HA 1 TA 0 - 6.6.1.4
Adapter driver:      <IDE>                     HA 1
=== Scsi-Device-Map ===
CdRomPeripheral      : _NEC DVD_RW ND-1300A             atapi Port 1 ID 0  DMA: On
CdRomPeripheral      : CDWRITER IDE5224                 atapi Port 1 ID 1  DMA: On
DiskPeripheral       : ST3120022A              3.54   si3112r Port 2 ID 0  DMA: Off
DiskPeripheral       : WDC WD2500KS-00MJB0     02.0   si3112r Port 2 ID 0  DMA: Off
=== CDRom-Device-Map ===
CDWRITER IDE5224           E:   CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE           : 0
Physical memory     : 1023MB (1048048kB)
Free physical memory: 562MB (576144kB)
Memory in use       : 45 %
Uncached PFiles: 0x0
Use Inquiry    : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
24.11.2007
CD-ROM (ISO)
3:59:29 PM #1 Text 0 File Isodoc.cpp, Line 6475
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate                : FALSE
Write                   : TRUE
Finalize CD             : FALSE
Multisession            : TRUE
Multisession type:      : Start multisession
Burning mode            : TAO
Mode                    : 1
ISO Level               : 1 (Max. of 11 = 8 + 3 char)
Character set           : ISO 9660
Joliet                  : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path  : TRUE
Write ISO9660 ;1 file extensions        : TRUE

3:59:29 PM #2 Text 0 File Burncd.cpp, Line 3012
CDWRITER IDE5224
Super Link activated

3:59:29 PM #3 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 81920KB of Memory

3:59:29 PM #4 Text 0 File Reader.cpp, Line 124
Reader running

3:59:29 PM #5 Text 0 File Writer.cpp, Line 122
Writer CDWRITER IDE5224          running

3:59:29 PM #6 ISO9660GEN -11 File geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)

3:59:36 PM #7 Text 0 File Burncd.cpp, Line 3305
Turn on Track-At-Once, using CD-R/RW media

3:59:50 PM #8 Text 0 File DlgWaitCD.cpp, Line 281
Last possible write address on media:   359845 ( 79:59.70)
Last address to be written:             187374 ( 41:40.24)

3:59:50 PM #9 Text 0 File DlgWaitCD.cpp, Line 293
Write in overburning mode: NO (enabled: CD)

3:59:50 PM #10 Text 0 File DlgWaitCD.cpp, Line 2612
Recorder: CDWRITER IDE5224;
   CDR code: 00 97 26 66; OSJ entry from: CMC Magnetics Corporation
   ATIP Data:
     Special    Info [hex] 1: D0 00 98, 2: 61 1A 42 (LI 97:26.66), 3: 4F 3B 47 (LO 79:59.71)
     Additional Info [hex] 1: 00 00 80 (invalid), 2: 00 80 00 (invalid), 3: 00 80 80 (invalid)

3:59:50 PM #11 Text 0 File DlgWaitCD.cpp, Line 459
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert the disc to write to.
 (Medium in drive: Unknown. Medium required by compilation: CD-R/RW.)

3:59:50 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
    2 indices, index0 (150) not provided
    original disc pos #0 + 187375 (187375) = #187375/41:38.25
    relocatable, disc pos for caching/writing not required/ required, no patch infos
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 187373 blocks [CDWRITER IDE5224]
--------------------------------------------------------------

3:59:50 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [CDWRITER IDE5224] for write in TAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc not fixated
Tracks 1 to 1:
   1: TRM_DATA_MODE1, 2048/0x00, FilePos             0        307200     384051200, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
    -150 |  lead-in |   0 |    0x41 | 0x00
    -150 |        1 |   0 |    0x41 | 0x00
       0 |        1 |   1 |    0x41 | 0x00
  187375 | lead-out |   1 |    0x41 | 0x00

3:59:50 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 1127
Removed 2 run-out blocks from end of track 1. Length: 187375 -> 187373.

3:59:50 PM #15 Text 0 File SCSIPassThrough.cpp, Line 38
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

3:59:50 PM #16 Text 0 File SCSIPassThrough.cpp, Line 83
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

3:59:51 PM #17 Phase 24 File dlgbrnst.cpp, Line 1685
Caching of files started

3:59:51 PM #18 Text 0 File Burncd.cpp, Line 4145
Cache writing successful.

3:59:51 PM #19 Phase 25 File dlgbrnst.cpp, Line 1685
Caching of files completed

3:59:51 PM #20 Phase 36 File dlgbrnst.cpp, Line 1685
Burn process started at 52x (7,800 KB/s)

3:59:51 PM #21 Text 0 File ThreadedTransferInterface.cpp, Line 2685
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

3:59:51 PM #22 Text 0 File Mmc.cpp, Line 21840
Set BUFE: Super Link -> ON

4:01:45 PM #23 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

4:01:49 PM #24 Text 0 File Mmc.cpp, Line 16608
<CDWRITERIDE5224         > start Close Session

4:02:08 PM #25 Phase 37 File dlgbrnst.cpp, Line 1685
Burn process completed successfully at 52x (7,800 KB/s)
 
4:02:08 PM #26 Text 0 File Burncd.cpp, Line 4629
Buffer underrun error was avoided 2 times.

4:02:23 PM #27 Phase 78 File dlgbrnst.cpp, Line 1685
Data verification started

4:02:26 PM #28 Text 0 File ThreadedTransferInterface.cpp, Line 1127
Removed 2 run-out blocks from end of track 1. Length: 187375 -> 187373.

|-- 4:02:30 PM #29 SectorVerify 11 File Cdrdrv.cpp, Line 9771
|    Sector 1121 on disc has different content to source

|   NOTE - for the sake of brevity, I removed a bunch of lines. 
|   Al the lines between #29 (above) and #780 (below) were the same.
|   All were "Line 9771" but different "Sectors numbers" listed.
|
|   4:43 PM #780 Text 0 File ThreadedTransfer.cpp, Line 228
|- writers idle, stopping conversion
 
4:04:43 PM #781 SectorVerify 11 File Cdrdrv.cpp, Line 9771
Sector 187150 on disc has different content to source

4:04:43 PM #782 Phase 81 File dlgbrnst.cpp, Line 1685
Data verification failed

Existing drivers:
File 'Drivers\ASPI32.SYS': Ver=4.71 (0001), size=17005 bytes, created 5/28/2003 6:53:46 PM
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
Post #: 1
RE: Help with a "burning" issue... - 11/24/2007 5:25:51 PM   
chugbug

 

Posts: 5
Joined: 11/24/2007
Status: offline
Back again... Update on my DVD Drive... Got it working again.  I deleted it (uninstalled in Device Manager) and reinstalled it again.  Seems to work fine again.

Thanks...Chugbug

(in reply to chugbug)
Post #: 2
RE: Help with a "burning" issue... - 11/24/2007 8:01:21 PM   
SithTracy


Posts: 1670
Status: offline
chugbug... Welcome...glad you got things worked out.

(in reply to chugbug)
Post #: 3
RE: Help with a "burning" issue... - 11/26/2007 12:17:19 PM   
chugbug

 

Posts: 5
Joined: 11/24/2007
Status: offline
Sith... Got my DVD working, but STILL have the issue with CDRW as outline in original post (burn sucessful, but errors found during confirmation).

I GUESS, since the burns seem to be fine, I could just TURN OFF (uncheck) the verification?  Although all that may be doing is hiding a problem.

Suggestions appreciated...Chugbug

(in reply to SithTracy)
Post #: 4
RE: Help with a "burning" issue... - 11/26/2007 12:52:09 PM   
SithTracy


Posts: 1670
Status: offline
What brand of CD-RW are you writing to?  I have only had consistent luck with Verbatim, but generally I don't use them.  I've got a bunch of useless TDK CD-RW media that none of my drives recognize...  I just burn to DVD±R/CD-R these days and don't bother with any RW media.

(in reply to chugbug)
Post #: 5
RE: Help with a "burning" issue... - 11/26/2007 5:26:44 PM   
chugbug

 

Posts: 5
Joined: 11/24/2007
Status: offline
Using TDK's from a 100 pk bundle I've had for a few years.  I've been using these for quite a while, and haven't had issues.  I have several computers, and I don't have any problems burning them on any of the other burners (a NEC DVD burner on same machine, plus other CDRW's on other pcs-- one with an Artec CDRW, another has a Plextor2410 CDRW).

I tried using a different brand disk ( Maxwell), but had same problem in the verification.

I've had this burner for over 4 years (purchased in June 2003), and as I said, I've been using the same discs for about the same time.  When the problem first started a few months ago, I assumed it was the CD's, but when I tried some others I had, had the same results.  Then when I could burn to the CD's on my DVD burner, it kind of narrowed it down. 

I tired running a head cleaner CD, but didn't help.  A few days ago after finally getting some time to work on the problem, I downloaded and updated the firmware from the original to the latest one on the Pacific Digital website (http://www.pacificdigital.com/dl/pafiledb.php?action=file&id=17).  The firmware update ran and said it was sucessful.  Old version was .0012, new says it's .001H (using Sandra Lite XI).

Thanks...chugbug

(in reply to SithTracy)
Post #: 6
RE: Help with a "burning" issue... - 11/26/2007 7:05:04 PM   
SithTracy


Posts: 1670
Status: offline
quote:

I tired running a head cleaner CD, but didn't help
Yikes... that was probably not a good idea.  Those things were made for playback devices only, not for burners.  Might be time for a new burner...

(in reply to chugbug)
Post #: 7
RE: Help with a "burning" issue... - 11/27/2007 2:38:38 PM   
chugbug

 

Posts: 5
Joined: 11/24/2007
Status: offline
Yikes... that was probably not a good idea.  Those things were made for playback devices only, not for burners. 

Hmmmm.   Not sure if this was the first time I used it or not on this burner, BUT I use it regularly on my Plextor burner in my studio (workshop) 'cause of the dust build-up.  Hasn't seem to hurt it though, but don't use it for burning very often now since flash drives came out.  (Mostly used it to listen to music, but now I listen to Sirius radio on my pc.)  Since I don't use that one very often, I always used the cleaner just before I used it.

What would be wrong with doing this?  All it is is a set of brushes that goes over and "dusts off" the eye (Kensington "Drive Guardian").  Are the burners THAT much different?  Could it mis-align the eye??  Never gave it a thought that there would be that much of a difference between.

BUT... if it's not good to do so, I'll definitely discontinue the practice. 

While I've got you... Probably should have asked this question BEFORE I ordered it, but was an impulse buy.  TigerDirect had a Samsung SH-S182M DVD+RW Light-scribe on their Thanksgiving day sale for $25.00.   Also ordered a 50 pk of MEMOREX disks.  I usually have good luck with Memorex, but never had a Light Scribe before.  Are there any quirks to watch out for with them??   Guess I shouldn't use the cleaner on it... huh? ;)

Thanks...Chugbug

(in reply to SithTracy)
Post #: 8
RE: Help with a "burning" issue... - 11/27/2007 8:18:18 PM   
MP3Mogul


Posts: 5743
Joined: 4/11/2002
From: Retired Moderator
Status: offline
The drive is fine, but GET RID OF THE MEMOREX as they are rubbish!

The Verbatim LiteScribe are fantastic, never had a problem with them.


_____________________________



LG GSA H22L Firm 1.02
Samsung SH-203N Firm SB01
LiteOn SOHD-16P9S Firm FS0D

(in reply to chugbug)
Post #: 9
Page:   [1]
All Forums >> [Optical Storage] >> CD, DVD, BD Drives >> Help with a "burning" issue... Page: [1]
Jump to:





New Messages No New Messages
Hot Topic w/ New Messages Hot Topic w/o New Messages
Locked w/ New Messages Locked w/o New Messages
 Post New Thread
 Reply to Message
 Post New Poll
 Submit Vote
 Delete My Own Post
 Delete My Own Thread
 Rate Posts




Forum Software © ASPPlayground.NET Advanced Edition 2.4.5 ANSI

0.141