|
chugbug -> Help with a "burning" issue... (11/24/2007 5:01:20 PM)
|
Hello All,
I have a Pacific Digial Mach 52 CDRW (shows in hardware list as CDWRITER IDE5224). For some reason, a few months ago, I started having problems burning disks with it. Today, I updated the firmware, then tried to burn a test disk.
Using NERO 6, I burned a disk with 362MB of files/folders. According to the log, the burn was sucessful, but the verification found errors. I checked the burned disk, and it opens fine, has the same amount of data/files/folders as it should, and I can read the disk. Hoping it was a fluke, I burned another, but the same thing happened. Anyone have any suggestions as to what the problem may be? Listed below is the log from the last burn.
Also, Now a more pressing issue... I went into my Device Manager for the exact name that the CDRW disk is shown, and I noticed that now my DVD burner is "X" out and disabled. I attempted to enable it, but Windows says it can't. I KNOW I upgraded the firmware to the correct drive (I made a copy of the window after it was finished, and it shows the correct drive was selected). So now, it appears I have two problems!
I wasn't too concerned about the issue with the CDRW, since it seemed to have burned the data, plus I had my DVD burner to use instead. But now that I can't access my DVD drive, I need to figure out what happened to it.
Can anyone give me some recommendations to my problems 1) DVD drive not being able to be enabled, 2) why my CDRW burns appear to be not burrning exactly as it should.
Thanks...Chugbug
-------------------------------------------------------------------------
NERO 6 Burn Log:
John E. Brady
[REMOVED]
Windows XP 5.1
IA32
WinAspi: File 'Wnaspi32.dll': Ver=4.71 (0001), size=45056 bytes, created 5/28/2003 6:53:46 PM
ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM
NT-SPTI used
Nero Version: 6.6.1.4
Internal Version: 6, 6, 1, 4d
(Nero Express)
Recorder: <CDWRITER IDE5224> Version: 001H - HA 1 TA 0 - 6.6.1.4
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <CDWRITER IDE5224 >Version: 001H - HA 1 TA 0 - 6.6.1.4
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
CdRomPeripheral : _NEC DVD_RW ND-1300A atapi Port 1 ID 0 DMA: On
CdRomPeripheral : CDWRITER IDE5224 atapi Port 1 ID 1 DMA: On
DiskPeripheral : ST3120022A 3.54 si3112r Port 2 ID 0 DMA: Off
DiskPeripheral : WDC WD2500KS-00MJB0 02.0 si3112r Port 2 ID 0 DMA: Off
=== CDRom-Device-Map ===
CDWRITER IDE5224 E: CDRom0
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1023MB (1048048kB)
Free physical memory: 562MB (576144kB)
Memory in use : 45 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
24.11.2007
CD-ROM (ISO)
3:59:29 PM #1 Text 0 File Isodoc.cpp, Line 6475
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : TAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
3:59:29 PM #2 Text 0 File Burncd.cpp, Line 3012
CDWRITER IDE5224
Super Link activated
3:59:29 PM #3 Text 0 File ThreadedTransfer.cpp, Line 531
ReadBuffer-Pipe got 81920KB of Memory
3:59:29 PM #4 Text 0 File Reader.cpp, Line 124
Reader running
3:59:29 PM #5 Text 0 File Writer.cpp, Line 122
Writer CDWRITER IDE5224 running
3:59:29 PM #6 ISO9660GEN -11 File geniso.cpp, Line 3312
First writeable address = 0 (0x00000000)
3:59:36 PM #7 Text 0 File Burncd.cpp, Line 3305
Turn on Track-At-Once, using CD-R/RW media
3:59:50 PM #8 Text 0 File DlgWaitCD.cpp, Line 281
Last possible write address on media: 359845 ( 79:59.70)
Last address to be written: 187374 ( 41:40.24)
3:59:50 PM #9 Text 0 File DlgWaitCD.cpp, Line 293
Write in overburning mode: NO (enabled: CD)
3:59:50 PM #10 Text 0 File DlgWaitCD.cpp, Line 2612
Recorder: CDWRITER IDE5224;
CDR code: 00 97 26 66; OSJ entry from: CMC Magnetics Corporation
ATIP Data:
Special Info [hex] 1: D0 00 98, 2: 61 1A 42 (LI 97:26.66), 3: 4F 3B 47 (LO 79:59.71)
Additional Info [hex] 1: 00 00 80 (invalid), 2: 00 80 00 (invalid), 3: 00 80 80 (invalid)
3:59:50 PM #11 Text 0 File DlgWaitCD.cpp, Line 459
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert the disc to write to.
(Medium in drive: Unknown. Medium required by compilation: CD-R/RW.)
3:59:50 PM #12 Text 0 File ThreadedTransferInterface.cpp, Line 847
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 187375 (187375) = #187375/41:38.25
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 187373 blocks [CDWRITER IDE5224]
--------------------------------------------------------------
3:59:50 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 1059
Prepare recorder [CDWRITER IDE5224] for write in TAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc not fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 384051200, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
-150 | lead-in | 0 | 0x41 | 0x00
-150 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
187375 | lead-out | 1 | 0x41 | 0x00
3:59:50 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 1127
Removed 2 run-out blocks from end of track 1. Length: 187375 -> 187373.
3:59:50 PM #15 Text 0 File SCSIPassThrough.cpp, Line 38
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
3:59:50 PM #16 Text 0 File SCSIPassThrough.cpp, Line 83
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME
3:59:51 PM #17 Phase 24 File dlgbrnst.cpp, Line 1685
Caching of files started
3:59:51 PM #18 Text 0 File Burncd.cpp, Line 4145
Cache writing successful.
3:59:51 PM #19 Phase 25 File dlgbrnst.cpp, Line 1685
Caching of files completed
3:59:51 PM #20 Phase 36 File dlgbrnst.cpp, Line 1685
Burn process started at 52x (7,800 KB/s)
3:59:51 PM #21 Text 0 File ThreadedTransferInterface.cpp, Line 2685
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
3:59:51 PM #22 Text 0 File Mmc.cpp, Line 21840
Set BUFE: Super Link -> ON
4:01:45 PM #23 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
4:01:49 PM #24 Text 0 File Mmc.cpp, Line 16608
<CDWRITERIDE5224 > start Close Session
4:02:08 PM #25 Phase 37 File dlgbrnst.cpp, Line 1685
Burn process completed successfully at 52x (7,800 KB/s)
4:02:08 PM #26 Text 0 File Burncd.cpp, Line 4629
Buffer underrun error was avoided 2 times.
4:02:23 PM #27 Phase 78 File dlgbrnst.cpp, Line 1685
Data verification started
4:02:26 PM #28 Text 0 File ThreadedTransferInterface.cpp, Line 1127
Removed 2 run-out blocks from end of track 1. Length: 187375 -> 187373.
|-- 4:02:30 PM #29 SectorVerify 11 File Cdrdrv.cpp, Line 9771
| Sector 1121 on disc has different content to source
|
| NOTE - for the sake of brevity, I removed a bunch of lines.
| Al the lines between #29 (above) and #780 (below) were the same.
| All were "Line 9771" but different "Sectors numbers" listed.
|
| 4:43 PM #780 Text 0 File ThreadedTransfer.cpp, Line 228
|- writers idle, stopping conversion
4:04:43 PM #781 SectorVerify 11 File Cdrdrv.cpp, Line 9771
Sector 187150 on disc has different content to source
4:04:43 PM #782 Phase 81 File dlgbrnst.cpp, Line 1685
Data verification failed
Existing drivers:
File 'Drivers\ASPI32.SYS': Ver=4.71 (0001), size=17005 bytes, created 5/28/2003 6:53:46 PM
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
|
|
|
|
