CDRInfo Forum CDRInfo Forum

Forums  Register  Login  My Profile  Inbox  Address Book  My Subscription  My Forums 

Photo Gallery  Member List  Search  Calendars  FAQ  Ticket List  Log Out

Hdd Jumper Settings   Logged in as: Guest
Viewers: 1325 You can click here to see Today's Posts | Most Active Topics | Posts Since Last Visit
  Printable Version
All Forums >> [Other] >> Game consoles >> Hdd Jumper Settings Page: [1]
Login
Message << Older Topic   Newer Topic >>
Hdd Jumper Settings - 11/9/2005 5:58:35 PM   
Ryozuki


Posts: 4
Joined: 11/9/2005
Status: offline
This is my first post on this site and I hope I get some responses! I actually have a problem finding the jumper settings for the Official PS2 HDD (I am trying to connect it to my PC.) and can not set the hard drive to slave or master. If anyone knows the correct settings for the HDD and can show me plz help me out! Thank everyone in advance for any offered help.
Post #: 1
RE: Hdd Jumper Settings - 11/9/2005 6:40:11 PM   
SiliconFreak


Posts: 12103
Joined: 7/4/2003
From: Melbourne, Victoria, AUS
Status: offline
Hi again....sorry but dont know very much about PS2 - PC Harddisk compatibility....but if its possible...then (in case you already have a boot-HDD with some OS in your PC )...then set your PS2 HDD to slave (with jumpers on HDD) and it should work just fine (although i am not sure about PS2's file system!?) - otherwise you would need to format it into FAT or NTFS....and then it should work just fine....

I hope Emperor (or some other members) will come by and tell you more about it....cause he is a REAL PS2 freak....

Good luck!

SF.

(in reply to Ryozuki)
Post #: 2
RE: Hdd Jumper Settings - 11/9/2005 7:16:12 PM   
SithTracy


Posts: 1670
Status: offline
Sorry, don't own a PS2, but if there are no jumper settings, perhaps it defaults to CS/Cable Select.  Make it the only device on your secondary IDE controller.

(in reply to Ryozuki)
Post #: 3
RE: Hdd Jumper Settings - 11/9/2005 8:01:24 PM   
Ryozuki


Posts: 4
Joined: 11/9/2005
Status: offline
Thanks for that info guys but the hdd that I have has the jumper clip things on the back of it. I was just trying to find out if anyone knew which prongs the clips should go on to set it to a slave drive. The PS2 hdd is not set to either and I need to know what the clip config is to set it to that. That  to much of a techy kinda guy so thats the best description of my problem I can give. If too confusing just let me know.... thx for the fast post though.

(in reply to Ryozuki)
Post #: 4
RE: Hdd Jumper Settings - 11/16/2005 4:12:58 AM   
emperor


Posts: 7210
Joined: 4/28/2004
Status: offline
there must be some kind of jumper at the back, just test and trial to see what will work

(in reply to Ryozuki)
Post #: 5
Page:   [1]
All Forums >> [Other] >> Game consoles >> Hdd Jumper Settings Page: [1]
Jump to:





New Messages No New Messages
Hot Topic w/ New Messages Hot Topic w/o New Messages
Locked w/ New Messages Locked w/o New Messages
 Post New Thread
 Reply to Message
 Post New Poll
 Submit Vote
 Delete My Own Post
 Delete My Own Thread
 Rate Posts




Forum Software © ASPPlayground.NET Advanced Edition 2.4.5 ANSI

0.031